Shop services
Six stations, one continuous edge
Every service below is a real station on the bench of Baoji Haixuanda Industrial Co., Ltd. and each one hands a clearly recorded result to the next. Read the six descriptions in order and you will have the full picture of how a job moves through our whetstone shop at Room 0401 Unit 1 Building 4 Courtyard 3 Lianmeng Road, Jintai District, Baoji - 721000, China (CN).
Grind Bay Desk
The grind bay desk is the front door of the shop. When a piece arrives, a technician records the owner, the reference number, the condition of the existing edge and the finish the partner expects. Photographs are taken at receipt so there is never a later argument about a mark that was already there. The desk then writes a grind plan that names the grit progression, the number of passes and the bench that will carry the work.
This is also the station that quotes and schedules. Because the plan is written before any stone is touched, the estimate we give is based on the actual work rather than a hopeful guess. If the plan changes during the job, the desk contacts the partner before the change is made, not after. Queries about a job in progress go to the desk first, and we answer within one bench day.
What to bring
Bring the piece itself, any drawing or tolerance sheet you have, and a note on the working environment the edge will face. We do not need a polished purchase order to assess a job; a clear description is enough for the desk to log an intake and issue a plan.
Honing Row Rounds
The honing rows are long benches set with matched stones at fixed grades. Our technicians do not work a single piece from start to finish in isolation; they walk the rows in rounds, taking every piece in the batch one grit further on each pass. This is slower per piece and far faster per batch, because the stones stay clean, the slurry stays consistent and the pressure stays identical from unit to unit.
A round begins with a flatness check on every stone in the line. Any stone that has lost its grade is taken out before work continues, and a replacement is marked and seated. The technician then runs the batch, records the pass count and finishes the round by wiping the stones and clearing slurry. Nothing is left overnight on a wet stone, because a stone left with slurry dries unevenly and will not hold a grade.
Consistency you can measure
Because rounds treat every unit equally, the spread across a batch is narrow. Partners who need a hundred pieces to behave like a hundred copies of the first piece are the clients this station was built for, and they usually find us after a supplier has had a bad spread on a large order.
Strop Weeks
Strop weeks are scheduled blocks on the shop calendar when every leather strop in service is reconditioned, dressed and inspected. A strop is a simple tool and easy to neglect, which is exactly why the trade is full of fabled edges that were really just good leather with clean compound. We replace compound on a fixed cycle and we check every paddle for embedded grit before it goes back to the bench.
Each strop carries its own history: a date, the compound grade and the initials of the technician who dressed it. Paddles that have developed a hollow, a ridge or a contaminated patch are retired rather than patched, and a partner can ask to see the record for any paddle used on their work.
Why a fixed calendar
Stropping compound picks up stray abrasive and metal swarf slowly and invisibly. Left too long, it turns a finishing tool into a scratch source. A calendar removes the judgement call and makes the condition of every strop a matter of record. Partners using our shop under a standing arrangement receive a short note after each strop week.
Bevel Check Days
Bevel check days are set aside for geometry. Under a loupe and a light table, we measure the primary bevel against the drawing, inspect the edge line for waviness and record any drift from the intended angle. Results go into a running log with the batch reference and the initials of the technician who took the reading, so a batch can be reconstructed months after it left the shop.
Angle creep is the quiet fault of the edge trade. A bevel that drifts a degree across a long run will pass a quick glance and fail in service. Our check days exist to catch that drift on a fixed schedule, while the batch is still small enough to correct cheaply. Every batch leaving the shop carries a bevel record the partner can keep on file.
Reading the record
The record states the intended angle, the measured angle at three points along the edge, and a note on the surface finish of both faces. Where a partner has supplied a tolerance, the record flags any unit outside it. We do not hide out-of-tolerance units behind an average; the sheet names them.
Water Stone Sessions
Water stone sessions are working hours on the bench when we flatten, grade and re-seat our stone stock, and when we are happy to open the bay to visitors who want to see a stone behave before they commit to a specification. These are real sessions, not demonstrations, and attendees see the same slurry, grit marks and decisions that a normal working day produces.
A session usually begins with a stock walk: every stone in the rack is lifted, checked for flatness against a plate and marked with its grade and date. Stones that are still true go back on the rack. Stones that have gone off are re-flattened on the lapping plate, and those beyond recovery are retired with a note in the log. Visitors are welcome to bring a sample and run a pass under supervision.
Who should attend
Partners sourcing edge work for the first time, engineers who want to understand what a stone grade actually means in practice, and buyers who have been burned by a vague finish claim all get something from a session. Book at least a week ahead through the contact page, and tell the desk what you want to learn so the session is set up to answer it.
Edge Test Evenings
Edge test evenings close the week with a structured proof run. Every batch that is ready to leave runs the same protocol on paper, thread and a controlled shave check, in the same order, on the same equipment. The result is written down before the bench is cleaned, which keeps the pass or fail decision independent of who happens to be at the stone that evening.
The protocol is deliberately simple and deliberately repeatable. Paper is cut with a single controlled stroke and the edge is inspected under the loupe for any rolling. Thread is cut at a set tension to confirm the apex is free of burr. The shave check confirms that the edge is clean enough for the finish grade agreed at the desk. Each step produces a written line in the batch record.
Attendance and results
Any partner holding a sample in a ready batch is welcome to attend by appointment and watch their own work run the protocol. Results are handed over at the end of the evening or sent by email on the next bench day. There is no pressure to buy anything at an edge test evening; the point is the written proof.
How a job travels through the shop
The six stations are not a menu to be picked from in any order. They are a route. A job enters at the desk, travels the rounds, is dressed at the strop weeks, proved on a bevel check day and signed off at an edge test evening. The overview below shows the four broad stages every piece passes through.
Intake and plan
The desk logs the piece, photographs its condition and writes a grind plan naming grit, passes and bench.
Rounds and dressing
The batch walks the honing rows one grit per round, and strops are dressed on the strop week calendar.
Geometry and proof
A bevel check day measures the angle against the drawing and records any drift in the running log.
Edge test and handover
The proof protocol runs on the last evening of the week, results are written down, and the batch is released with its record.
Bring us a stubborn edge
Reach the grind bay desk at trade@haixuanda.buzz or +17248037498 and describe the piece. We will tell you which station it should start at and what the finish will be.